Fox face: Amigurumi Face Placement Planner

A narrow expression with angular cheeks

The fox study starts from a thirty-position, twelve-round reference. Eyes lie at positions eleven and nineteen on round six, but each eye is a sloping backstitched line rather than a filled oval. Its endpoints are 0.55 intervals to either side of the center, with the first two tenths of a round above and the second two tenths below. The two lines deliberately share the same slant. The cheek outlines, by contrast, are reflected around the front center.

Trace the cheek routes separately

The left cheek travels through position ten on round 6.5, eleven on round 7.6 and fourteen on round 7.2. The right cheek runs from twenty on round 6.5 through nineteen on round 7.6 to sixteen on round 7.2. Neither path closes, and neither joins across the center. These two open angular routes suggest a face boundary without making a separate muzzle patch. A filled white mask would require additional stitches and is outside the saved plan.

Keep the nose central despite the slanted eyes

A triangular nose spans positions 14.4 to 15.6 at round 6.7 and points downward to stitch fifteen on round 7.3. The central line and two curved mouth lobes follow underneath. Mark center stitch fifteen on every featured round before judging the asymmetry of the eye lines. If the head appears twisted, first inspect the actual front orientation and stuffing. Rotating one eye independently can conceal an orientation error while producing a different drawing.

Questions and practical fixes

Should both eye slopes face inward?

The exact example uses parallel slants. Mirrored slants are a valid new design decision, but they are not the geometry in this downloaded project.

Is the cheek a color-change crochet round?

No. It is a surface backstitch route on existing fabric. Its vertices do not consume or create head stitches.

Why is my cheek a smooth curve?

Join its three listed landmarks with short straight backstitches. The angular middle point is intentional, unlike the quadratic controls used for the mouth curves.

Exact setup, compatible head reference and finishing

Open the Amigurumi Face Placement Planner and choose fox, circumference 30, height 12 and eye separation 8. The reference below assumes an existing single-crochet head with six stitches in a magic ring, then six evenly distributed increases on each round until 30 stitches. Work three even rounds, then six evenly distributed decreases per round until six remain; close those final loops with the tail. This optional arithmetic reference has 12 worked rounds. Its maximum-count band provides a reference for the eye line and nearby feature anchors. Fractional curve controls are guide locations; check their position on the actual curved surface rather than assuming every referenced level has the maximum circumference. Swatch and finish a physical head before assessing the actual fit.

The placement tool generates embroidery instructions, not that head construction. Use a tapestry needle and suitable contrasting yarn, transfer temporary landmarks, then follow the complete paths below. Round coordinates increase downward on this unwrapped face map. Fractional locations lie between markers. Short backstitches follow straight paths; curved strands are couched to the drawn guide. Secure each separate tail inside without pulling the surface inward. Review the chart-reading guide and keep the exact project JSON with your chosen trial. US and UK modes retain the same coordinates. No physical crochet or toy certification is implied by the calculated example.

1. fox placement trial on an existing head: mark front center stitch 15. Eyes are centered at stitches 11 and 19 on round 6; separation 8 stitch intervals (7 numbered positions strictly between). left-eye: backstitch (10.45, R5.8) → (11.55, R6.2); yarn slot 2. right-eye: backstitch (18.45, R5.8) → (19.55, R6.2); yarn slot 2. nose: backstitch (14.4, R6.7) → (15.6, R6.7) → (15, R7.3), close to the first point; yarn slot 2. philtrum: backstitch (15, R7.3) → (15, R7.7); yarn slot 2. left-mouth: couch a curve from (14.2, R7.7) through control (14.6, R8.2) to (15, R7.7); yarn slot 2. right-mouth: couch a curve from (15, R7.7) through control (15.4, R8.2) to (15.8, R7.7); yarn slot 2. left-cheek: backstitch (10, R6.5) → (11, R7.6) → (14, R7.2); yarn slot 2. right-cheek: backstitch (20, R6.5) → (19, R7.6) → (16, R7.2); yarn slot 2. Fractional coordinates are between stitch or round markers; curve controls guide the shape and are not extra insertion points. Compare temporary threads on the stuffed head, then secure each separate strand inside without distorting the surface. This plan references 30 head positions; it does not make 30 new crochet stitches. [30 existing head reference positions]