Leaf bookmark: Crochet Bookmark Generator

Use a leaf pendant with a slim return-slip cord

This design keeps a sixteen-output leaf outside the book and uses a soft nineteen-slip-stitch cord between pages. Its main crochet workload is thirty-five outputs across two pieces. The leaf begins from eight chains, while the cord begins from twenty. Those foundations are separate budgets and must not be combined into one long chain that silently changes the leaf insertion route.

Work both sides of the eight-chain leaf foundation

Skip chain eight nearest the hook. On the outward side, work sc, hdc, dc, tr, dc and hdc into chains seven through two, followed by three sc in chain one. Rotate around the far end to the unused foundation-side loops. Return with hdc, dc, tr, dc and hdc in chains two through six, then two sc in chain seven. The starting sc and final two sc form the near tip's three outputs.

Join the cord at the near tip

For the separate cord, chain twenty, skip the nearest chain and slip stitch back through the remaining nineteen chains. Sew its first two return outputs respectively to leaf outputs one and sixteen. These are the near-tip references, not the far chain-one end. Pin both tacks before reinforcing and weave the tails into the back without crushing the graduated-height posts.

Keep the pendant and reading strand in different roles

The leaf can identify the bookmark above the cover while the flexible cord marks the page. Test whether the actual cord slides comfortably without a hard knot against the paper. A pendant that twists or hangs sideways may have been attached at only one insecure point or at the wrong tip. Inspect the saved source orientation before compensating by winding the cord around the leaf.

Does the leaf have a turning row?

It rotates around a chain end and works unused side loops. That differs from turning the whole fabric over for a second flat row.

Can cord length be changed?

The supported foundation is twelve through eighty chains, with one fewer return slip stitch than starting chains.

Exact original setup and complete working record

Open the Crochet Bookmark Generator and choose leaf. Set strip width to 4, strip rows to 24, cord foundation to twenty and fringe cut length to fifteen centimeters; inactive fields do not resize a fixed source. Download the complete original bookmark JSON before editing. Use compatible smooth, low-bulk yarn, a matching hook, removable markers, scissors and a tapestry needle.

The sequence below uses US terms: sc means single crochet, hdc half double, dc double and tr treble. Ch is chain and sl st slip stitch. UK mode translates the stitch names without changing the source coordinates, quantities or joining references. Check each count's unit: decorative chains, counted closures, routine joins, sewing tacks and cut strands are different things. Review the chart-reading guide and the gauge guide before comparing nominal dimensions.

Use Symbol Chart for insertion sources, Written Pattern for the complete route and Stitch Preview for corresponding loop schematics. These original vector views are not real photographs or evidence of a physically tested bookmark. Wash and measure the actual sample, weave every tail securely and test paper contact in an ordinary book. Save yarn, hook, measured gauge and finishing notes alongside the complete JSON. Keep bulky motifs and fringe outside the page stack.

Every row, component and separate finishing reference

1. Two-sided leaf pendant (make 1), round 1: Ch 8; number chains 1 at the slip-knot end through 8 nearest the hook. Skip chain 8. On the first side work sc in chain 7, hdc in 6, dc in 5, tr in 4, dc in 3, hdc in 2, then 3 sc in chain 1. Rotate around that tip without turning the fabric over. In the unused side loops work hdc in chain 2, dc in 3, tr in 4, dc in 5, hdc in 6, then 2 sc in chain 7. Sixteen completed stitches: three at each end chain and ten along the two sides. Sl st to the first sc to finish; this routine join is excluded. [16 counted outputs per copy]
2. Two-sided leaf pendant (make 1), round 2: Fasten off, weave the foundation tail into the wrong side and leave a suitable attachment tail. Block the unfilled applique without stretching; sew through the underside and bases rather than crushing visible tops. [0 finishing reference]
3. Soft return-slip cord (make 1), row 1: Ch 20. Skip the nearest chain. Sl st in the second chain from hook and each remaining chain: 19 slip stitches. Do not add an extra turning row. Leave both ends long enough for the stated attachment. Fasten off and retain suitable attachment tails. This cord is soft; it contains no rigid stem or hidden wire. [19 counted outputs per copy]
4. Sew cord return outputs1 and 2 respectively to leaf near-tip outputs1 and 16. Pin both references before reinforcing; the far three-sc tip stays free. Keep the leaf outside the book and the soft cord between pages. [2 leaf-to-cord sewing tacks]